96 lines
2.2 KiB
Plaintext
96 lines
2.2 KiB
Plaintext
|
M291 P"Grid bed compensation map and Z Probe trigger height will be cleared. Ok or Cancel?" R"WARNING" S3 ; User must click OK or cancel.
|
||
|
|
M291 P"Heights will be found in gcode console if logging successful gcode is enabled" R"Did you remember to enabled gcode logging?" S3
|
||
|
|
|
||
|
|
; Clear compensation map and Z probe trigger height
|
||
|
|
;
|
||
|
|
G28 ; home all axis
|
||
|
|
M561 ; Disable any current bed compensation
|
||
|
|
G90 ; Absolute positioning
|
||
|
|
T0 ; Activate first tool
|
||
|
|
M98 P"ZSpeedsSlow.g" ; Set lower speeds for Z homing and lower Z motor current
|
||
|
|
M913 Z50 ; Drop motor current to prevent damage in case of head crash
|
||
|
|
|
||
|
|
; Preheat to probing temps
|
||
|
|
;
|
||
|
|
M291 P"Preheating to bed to 60 and nozzle to 210 for accurate probing"
|
||
|
|
M104 S210 ; Set nozzle to 210 and release
|
||
|
|
M190 S60 ; Set bed to 60 and wait
|
||
|
|
M109 S210 ; Set nozzle to 210 and wait
|
||
|
|
|
||
|
|
M98 P"0:/macros/musical tunes/GetAttention.g"
|
||
|
|
|
||
|
|
; 1
|
||
|
|
;
|
||
|
|
M291 P"Nozzle will now move to center of bed to reset Z0 and calibrate probe" S3
|
||
|
|
M98 P"0:/macros/Calibration/Bed Leveling/1_Center Nozzle on Bed"
|
||
|
|
G90 G1 Z3 F400
|
||
|
|
M400
|
||
|
|
G92 Z4 ; Reset z to 8 to allow jogging up to touch bed to nozzle
|
||
|
|
M291 P"Jog the Z Axis until the bed and nozzle are touching and click OK" R"Setting Z=0" Z1 S3
|
||
|
|
M400
|
||
|
|
G92 Z0 ; Set z = 0
|
||
|
|
G90 G1 Z3 F400
|
||
|
|
M104 S0 ; Turn off hotend heater as it's no longer needed
|
||
|
|
M291 P"Probe will now move to center of bed and measure trigger height 10 times" R"ZProbe Trigger Height Calibration" T3
|
||
|
|
M400
|
||
|
|
M98 P"0:/macros/Calibration/Bed Leveling/1_Center Probe on Bed"
|
||
|
|
|
||
|
|
G1 Z5
|
||
|
|
M400
|
||
|
|
G30 S-1
|
||
|
|
M400
|
||
|
|
G1 Z5
|
||
|
|
M400
|
||
|
|
G30 S-1
|
||
|
|
M400
|
||
|
|
G1 Z5
|
||
|
|
M400
|
||
|
|
G30 S-1
|
||
|
|
M400
|
||
|
|
G1 Z5
|
||
|
|
M400
|
||
|
|
G30 S-1
|
||
|
|
M400
|
||
|
|
G1 Z5
|
||
|
|
M400
|
||
|
|
G30 S-1
|
||
|
|
M400
|
||
|
|
G1 Z5
|
||
|
|
M400
|
||
|
|
G30 S-1
|
||
|
|
M400
|
||
|
|
G1 Z5
|
||
|
|
M400
|
||
|
|
G30 S-1
|
||
|
|
M400
|
||
|
|
G1 Z5
|
||
|
|
M400
|
||
|
|
G30 S-1
|
||
|
|
M400
|
||
|
|
G1 Z5
|
||
|
|
M400
|
||
|
|
G30 S-1
|
||
|
|
M400
|
||
|
|
G1 Z5
|
||
|
|
M400
|
||
|
|
G30 S-3 ; measure probe height and set it.
|
||
|
|
M400
|
||
|
|
M500 P31 ; save trigger height to config-override.g
|
||
|
|
G1 Z5
|
||
|
|
|
||
|
|
M98 P"0:/macros/musical tunes/GetAttention.g"
|
||
|
|
|
||
|
|
; Turn off heaters
|
||
|
|
;
|
||
|
|
M104 S0 ; Set nozzle to 0 and release
|
||
|
|
M140 S0 ; Set bed to 0 and release
|
||
|
|
M98 P"ZSpeedsNormal.g" ; return to normal speeds
|
||
|
|
M98 P"CurrentsNormal.g"
|
||
|
|
M400
|
||
|
|
M291 P"Homing"
|
||
|
|
G28 ; Home Z
|
||
|
|
M84 ; turn off the motors
|
||
|
|
M291 P"Probing complete. Turning off heaters and homing axis. Check log for trigger heights and enter into config.g" S2
|
||
|
|
|
||
|
|
|