Initial commit from RatRig
This commit is contained in:
commit
8868cbddc8
11
bed.g
Normal file
11
bed.g
Normal file
@ -0,0 +1,11 @@
|
||||
; this script compensates for what the Z offset is
|
||||
; so if G31 P500 X-30 Y-15 Z1.7 then first probe will be at
|
||||
; X30 Y20 (when G30 P0 X0 Y5)
|
||||
|
||||
M561 ; clear any bed transform
|
||||
|
||||
G30 P0 X5 Y5 Z-99999 ; probe near a leadscrew
|
||||
G30 P1 X150 Y285 Z-99999 ; probe near a leadscrew
|
||||
G30 P2 X270 Y5 Z-99999 S3 ; probe near a leadscrew and calibrate 3 motors
|
||||
|
||||
G29 ; probe the bed and enable compensation
|
||||
91
config.g
Normal file
91
config.g
Normal file
@ -0,0 +1,91 @@
|
||||
; General preferences
|
||||
G90 ; send absolute coordinates...
|
||||
M83 ; ...but relative extruder moves
|
||||
M550 P"V-Core 3" ; set printer name
|
||||
M669 K1 ; CoreXY
|
||||
G29 S1 ; Set Units to Millimeters
|
||||
|
||||
; Network
|
||||
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
|
||||
M586 P0 S1 ; enable HTTP
|
||||
M586 P1 S0 ; disable FTP
|
||||
M586 P2 S0 ; disable Telnet
|
||||
|
||||
; Drives
|
||||
M569 P0.0 S1 D3 ; physical drive 0.0 goes forwards
|
||||
M569 P0.1 S1 D3 ; physical drive 0.1 goes forwards
|
||||
M569 P0.2 S1 D3 ; physical drive 0.2 goes forwards
|
||||
M569 P0.3 S1 D3 ; physical drive 0.3 goes forwards
|
||||
M569 P0.4 S1 D3 ; physical drive 0.4 goes forwards
|
||||
M569 P0.5 S1 D3 ; physical drive 0.5 goes forwards
|
||||
M584 X0.4 Y0.3 Z0.0:0.1:0.2 E0.5 ; set drive mapping
|
||||
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
|
||||
|
||||
M92 X80.00 Y80.00 Z800.00 ; set steps per mm
|
||||
M906 X1000 Y1000 Z800 I30 ; set motor currents (mA) and motor idle factor in per cent
|
||||
M84 S30 ; Set idle timeout
|
||||
|
||||
M566 X400.00 Y400.00 Z6.00 E120.00 P1 ; set maximum instantaneous speed changes (mm/min)
|
||||
M203 X10800.00 Y10800.00 Z1000.00 E3600.00 ; set maximum speeds (mm/min)
|
||||
M201 X3000.00 Y3000.00 Z100.00 E3600.00 ; set accelerations (mm/s^2)
|
||||
|
||||
; Axis Limits
|
||||
M208 X0 Y0 Z0 S1 ; set axis minima
|
||||
M208 X310 Y300 Z300 S0 ; set axis maxima
|
||||
|
||||
; Endstops
|
||||
M574 X1 S1 P"io1.in" ; configure active high endstops
|
||||
M574 Y2 S1 P"io0.in" ; configure active high endstops
|
||||
M574 Z1 S2 ; configure Z-probe endstop for low end on Z
|
||||
|
||||
M671 X-4.5:150:304.5 Y-4.52:305:-4.52 S5 ; define positions of Z leadscrews or bed levelling screws
|
||||
M557 X30:300 Y15:300 P5 ; define 5x5 mesh grid
|
||||
|
||||
; Heaters
|
||||
M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed" ; configure sensor 0 as thermistor on pin temp0
|
||||
M950 H0 C"out0" T0 ; create bed heater output on out5 and map it to sensor 0
|
||||
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
|
||||
M140 H0 ; map heated bed to heater 0
|
||||
M143 H0 S110 ; set temperature limit for heater 0 to 110C
|
||||
|
||||
;; Run Bed PID Tune!! Bellow is an example for a 300x300 bed
|
||||
;; M307 H0 A303.1 C356.7 D1.4 S1.00 V24.0 B0
|
||||
|
||||
; Fans
|
||||
M950 F0 C"out3" Q500 ; create fan 0 on pin out3 and set its frequency
|
||||
M106 P0 C"Hotend Fan" S0 H1 T45 L255 ; set fan 0 name and value. Thermostatic control turned on for Hotend
|
||||
M950 F1 C"out4" Q500 ; create fan 1 on pin out4 and set its frequency
|
||||
M106 P1 C"Layer Fan" S0 H-1 L255 ; set fan 1 name and value. Thermostatic control is turned off
|
||||
|
||||
; Tools
|
||||
M563 P0 D0 H1 F1 ; define tool 0
|
||||
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
|
||||
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
|
||||
|
||||
M950 H1 C"out1" T1 ; create nozzle heater output on out2 and map it to sensor 1
|
||||
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
|
||||
M143 H1 S250 ; set the maximum temperature in C for heater
|
||||
|
||||
; EVA 2 / BMG / E3D V6
|
||||
|
||||
M92 E415 ; set extruder steps per mm, 1.8 angle/step
|
||||
M906 E800 ; set extruder motor current (mA) and idle factor in per cent
|
||||
|
||||
M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.060000e-8 A"Hotend"
|
||||
;; Run Heater PID Tune!!
|
||||
;; M307 H1 A751.5 C196.6 D4.7 S1.00 V23.9 B0
|
||||
|
||||
; Z-Probe
|
||||
;; Inductive Probe
|
||||
; M558 P5 C"!io3.in" H5 F400 T5000 ; set Z probe type to unmodulated and the dive height + speeds
|
||||
; G31 P500 X-30 Y-15 Z0.20 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
|
||||
;; BLTouch
|
||||
; M950 S0 C"io2.out" ; Create a servo pin on io2
|
||||
; M558 P9 C"io2.in" H5 F500 T10800 A5 ; set Z probe type to unmodulated and the dive height + speeds
|
||||
; G31 P25 X-28.00 Y-13.00 Z0.90 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
|
||||
|
||||
M404 N1.75 D0.4 ; Filament width and nozzle diameter
|
||||
T0
|
||||
|
||||
; Pressure Advance
|
||||
; M572 D0 S0.10
|
||||
4
deployprobe.g
Normal file
4
deployprobe.g
Normal file
@ -0,0 +1,4 @@
|
||||
; deployprobe.g
|
||||
; Called to deploy a physical Z probe
|
||||
;
|
||||
M280 P0 S10 ; Deploy the BLTouch pin
|
||||
23
homeall.g
Normal file
23
homeall.g
Normal file
@ -0,0 +1,23 @@
|
||||
; BLTouch
|
||||
;M280 P0 S160 ; Precautionary alarm release
|
||||
;M280 P0 S90 ; Ensure the pin is raised
|
||||
|
||||
G91 ; relative positioning
|
||||
G1 H2 Z5 F6000 ; lift Z relative to current position
|
||||
G1 H1 X-625 Y605 F3600 ; move quickly to X and U axis endstops and stop there (first pass)
|
||||
G1 H1 X-625 F1800 ; move quickly to X and U axis endstops and stop there (first pass)
|
||||
G1 H1 Y605 F1800 ; move quickly to X and U axis endstops and stop there (first pass)
|
||||
G1 H2 X5 Y-5 F6000 ; go back a few mm
|
||||
G1 H1 X-625 Y605 F360 ; move slowly to X and U axis endstops once more (second pass)
|
||||
G1 H1 X-625 F360 ; move slowly to X and U axis endstops once more (second pass)
|
||||
G1 H1 Y605 F360 ; move slowly to X and U axis endstops once more (second pass)
|
||||
|
||||
G90 ; absolute positioning
|
||||
G1 X150 Y150 F10000 ; go to first probe point
|
||||
G30 ; home Z by probing the bed
|
||||
|
||||
G91 ; relative positioning
|
||||
G1 Z5 F100 ; lift Z relative to current position
|
||||
G90 ; absolute positioning
|
||||
G1 X0 Y0 F10000
|
||||
|
||||
9
homex.g
Normal file
9
homex.g
Normal file
@ -0,0 +1,9 @@
|
||||
G91 ; relative positioning
|
||||
;G1 H2 Z5 F6000 ; lift Z relative to current position
|
||||
G1 H1 X-625 F1800 ; move quickly to X axis endstop and stop there (first pass)
|
||||
G1 H2 X5 F6000 ; go back a few mm
|
||||
G1 H1 X-625 F360 ; move slowly to X axis endstop once more (second pass)
|
||||
;G1 H2 Z-5 F6000 ; lower Z again
|
||||
G90 ; absolute positioning
|
||||
|
||||
G1 X0 F6000
|
||||
9
homey.g
Normal file
9
homey.g
Normal file
@ -0,0 +1,9 @@
|
||||
G91 ; relative positioning
|
||||
;G1 H2 Z5 F6000 ; lift Z relative to current position
|
||||
G1 H1 Y605 F1800 ; move quickly to Y axis endstop and stop there (first pass)
|
||||
G1 Y-5 F6000 ; go back a few mm
|
||||
G1 H1 Y605 F360 ; move slowly to Y axis endstop once more (second pass)
|
||||
;G1 H2 Z-5 F6000 ; lower Z again
|
||||
G90 ; absolute positioning
|
||||
|
||||
G1 Y0 F6000
|
||||
15
homez.g
Normal file
15
homez.g
Normal file
@ -0,0 +1,15 @@
|
||||
; BLTouch
|
||||
;M280 P0 S160 ; Precautionary alarm release
|
||||
;M280 P0 S90 ; Ensure the pin is raised
|
||||
|
||||
G91 ; relative positioning
|
||||
G1 H2 Z5 F6000 ; lift Z relative to current position
|
||||
G90 ; absolute positioning
|
||||
G1 X150 Y150 F10000 ; go to first probe point
|
||||
G30 ; home Z by probing the bed
|
||||
|
||||
; Uncomment the following lines to lift Z after probing
|
||||
;G91 ; relative positioning
|
||||
;G1 Z5 F100 ; lift Z relative to current position
|
||||
;G90 ; absolute positioning
|
||||
|
||||
4
retractprobe.g
Normal file
4
retractprobe.g
Normal file
@ -0,0 +1,4 @@
|
||||
; retractprobe.g
|
||||
; Called to retract a physical Z probe
|
||||
;
|
||||
M280 P0 S90 ; Retract the BLTouch pin
|
||||
Loading…
x
Reference in New Issue
Block a user