Initial commit from RatRig

bed.g

@@ -0,0 +1,11 @@
+; this script compensates for what the Z offset is
+; so if G31 P500 X-30 Y-15 Z1.7 then first probe will be at
+; X30 Y20 (when G30 P0 X0 Y5)
+
+M561 ; clear any bed transform
+
+G30 P0 X5 Y5 Z-99999 ; probe near a leadscrew
+G30 P1 X150 Y285 Z-99999 ; probe near a leadscrew
+G30 P2 X270 Y5 Z-99999 S3 ; probe near a leadscrew and calibrate 3 motors
+
+G29  ; probe the bed and enable compensation

config.g

@@ -0,0 +1,91 @@
+; General preferences
+G90                                     ; send absolute coordinates...
+M83                                     ; ...but relative extruder moves
+M550 P"V-Core 3"                        ; set printer name
+M669 K1                                 ; CoreXY
+G29 S1                                  ; Set Units to Millimeters
+
+; Network
+M552 P0.0.0.0 S1                        ; enable network and acquire dynamic address via DHCP
+M586 P0 S1                              ; enable HTTP
+M586 P1 S0                              ; disable FTP
+M586 P2 S0                              ; disable Telnet
+
+; Drives
+M569 P0.0 S1 D3                         ; physical drive 0.0 goes forwards
+M569 P0.1 S1 D3                         ; physical drive 0.1 goes forwards
+M569 P0.2 S1 D3                         ; physical drive 0.2 goes forwards
+M569 P0.3 S1 D3                         ; physical drive 0.3 goes forwards
+M569 P0.4 S1 D3                         ; physical drive 0.4 goes forwards
+M569 P0.5 S1 D3                         ; physical drive 0.5 goes forwards
+M584 X0.4 Y0.3 Z0.0:0.1:0.2 E0.5        ; set drive mapping
+M350 X16 Y16 Z16 E16 I1                 ; configure microstepping with interpolation
+
+M92 X80.00 Y80.00 Z800.00               ; set steps per mm
+M906 X1000 Y1000 Z800 I30               ; set motor currents (mA) and motor idle factor in per cent
+M84 S30                                 ; Set idle timeout
+
+M566 X400.00 Y400.00 Z6.00 E120.00 P1          ; set maximum instantaneous speed changes (mm/min)
+M203 X10800.00 Y10800.00 Z1000.00 E3600.00     ; set maximum speeds (mm/min)
+M201 X3000.00 Y3000.00 Z100.00 E3600.00        ; set accelerations (mm/s^2)
+
+; Axis Limits
+M208 X0 Y0 Z0 S1                               ; set axis minima
+M208 X310 Y300 Z300 S0                         ; set axis maxima
+
+; Endstops
+M574 X1 S1 P"io1.in"                           ; configure active high endstops
+M574 Y2 S1 P"io0.in"                           ; configure active high endstops
+M574 Z1 S2                                     ; configure Z-probe endstop for low end on Z
+
+M671 X-4.5:150:304.5 Y-4.52:305:-4.52 S5       ; define positions of Z leadscrews or bed levelling screws
+M557 X30:300 Y15:300 P5                        ; define 5x5 mesh grid
+
+; Heaters
+M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed"    ; configure sensor 0 as thermistor on pin temp0
+M950 H0 C"out0" T0                                     ; create bed heater output on out5 and map it to sensor 0
+M307 H0 B0 S1.00                                       ; disable bang-bang mode for the bed heater and set PWM limit
+M140 H0                                                ; map heated bed to heater 0
+M143 H0 S110                                           ; set temperature limit for heater 0 to 110C
+
+;; Run Bed PID Tune!! Bellow is an example for a 300x300 bed
+;; M307 H0 A303.1 C356.7 D1.4 S1.00 V24.0 B0
+
+; Fans
+M950 F0 C"out3" Q500                   ; create fan 0 on pin out3 and set its frequency
+M106 P0 C"Hotend Fan" S0 H1 T45 L255   ; set fan 0 name and value. Thermostatic control turned on for Hotend
+M950 F1 C"out4" Q500                   ; create fan 1 on pin out4 and set its frequency
+M106 P1 C"Layer Fan" S0 H-1 L255       ; set fan 1 name and value. Thermostatic control is turned off
+
+; Tools
+M563 P0 D0 H1 F1           ; define tool 0
+G10 P0 X0 Y0 Z0            ; set tool 0 axis offsets
+G10 P0 R0 S0               ; set initial tool 0 active and standby temperatures to 0C
+
+M950 H1 C"out1" T1         ; create nozzle heater output on out2 and map it to sensor 1
+M307 H1 B0 S1.00           ; disable bang-bang mode for heater and set PWM limit
+M143 H1 S250               ; set the maximum temperature in C for heater
+
+; EVA 2 / BMG / E3D V6
+
+M92 E415          ; set extruder steps per mm, 1.8 angle/step
+M906 E800         ; set extruder motor current (mA) and idle factor in per cent
+
+M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.060000e-8 A"Hotend"  
+;; Run Heater PID Tune!! 
+;; M307 H1 A751.5 C196.6 D4.7 S1.00 V23.9 B0
+
+; Z-Probe
+;; Inductive Probe
+; M558 P5 C"!io3.in" H5 F400 T5000       ; set Z probe type to unmodulated and the dive height + speeds
+; G31 P500 X-30 Y-15 Z0.20               ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
+;; BLTouch
+; M950 S0 C"io2.out"                     ; Create a servo pin on io2
+; M558 P9 C"io2.in" H5 F500 T10800 A5    ; set Z probe type to unmodulated and the dive height + speeds
+; G31 P25 X-28.00 Y-13.00 Z0.90          ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
+
+M404 N1.75 D0.4                                 ; Filament width and nozzle diameter
+T0
+
+; Pressure Advance
+; M572 D0 S0.10

deployprobe.g

@@ -0,0 +1,4 @@
+; deployprobe.g
+; Called to deploy a physical Z probe
+;
+M280 P0 S10															; Deploy the BLTouch pin

homeall.g

@@ -0,0 +1,23 @@
+; BLTouch
+;M280 P0 S160           ; Precautionary alarm release
+;M280 P0 S90            ; Ensure the pin is raised
+
+G91                     ; relative positioning
+G1 H2 Z5 F6000          ; lift Z relative to current position
+G1 H1 X-625 Y605 F3600 ; move quickly to X and U axis endstops and stop there (first pass)
+G1 H1 X-625 F1800 ; move quickly to X and U axis endstops and stop there (first pass)
+G1 H1 Y605 F1800 ; move quickly to X and U axis endstops and stop there (first pass)
+G1 H2 X5 Y-5 F6000       ; go back a few mm
+G1 H1 X-625 Y605 F360  ; move slowly to X and U axis endstops once more (second pass)
+G1 H1 X-625 F360  ; move slowly to X and U axis endstops once more (second pass)
+G1 H1 Y605 F360  ; move slowly to X and U axis endstops once more (second pass)
+
+G90                     ; absolute positioning
+G1 X150 Y150 F10000 ; go to first probe point
+G30                     ; home Z by probing the bed
+
+G91                    ; relative positioning
+G1 Z5 F100             ; lift Z relative to current position
+G90                    ; absolute positioning
+G1 X0 Y0 F10000
+

homex.g

@@ -0,0 +1,9 @@
+G91               ; relative positioning
+;G1 H2 Z5 F6000    ; lift Z relative to current position
+G1 H1 X-625 F1800 ; move quickly to X axis endstop and stop there (first pass)
+G1 H2 X5 F6000    ; go back a few mm
+G1 H1 X-625 F360  ; move slowly to X axis endstop once more (second pass)
+;G1 H2 Z-5 F6000   ; lower Z again
+G90               ; absolute positioning
+
+G1 X0 F6000

homey.g

@@ -0,0 +1,9 @@
+G91               ; relative positioning
+;G1 H2 Z5 F6000    ; lift Z relative to current position
+G1 H1 Y605 F1800 ; move quickly to Y axis endstop and stop there (first pass)
+G1 Y-5 F6000     ; go back a few mm
+G1 H1 Y605 F360  ; move slowly to Y axis endstop once more (second pass)
+;G1 H2 Z-5 F6000   ; lower Z again
+G90               ; absolute positioning
+
+G1 Y0 F6000

homez.g

@@ -0,0 +1,15 @@
+; BLTouch
+;M280 P0 S160           ; Precautionary alarm release
+;M280 P0 S90            ; Ensure the pin is raised
+
+G91               ; relative positioning
+G1 H2 Z5 F6000    ; lift Z relative to current position
+G90               ; absolute positioning
+G1 X150 Y150 F10000 ; go to first probe point
+G30               ; home Z by probing the bed
+
+; Uncomment the following lines to lift Z after probing
+;G91              ; relative positioning
+;G1 Z5 F100       ; lift Z relative to current position
+;G90              ; absolute positioning
+

retractprobe.g

@@ -0,0 +1,4 @@
+; retractprobe.g
+; Called to retract a physical Z probe
+;
+M280 P0 S90													; Retract the BLTouch pin