diff --git a/bed.g b/bed.g index ee9ba44..411ac2e 100644 --- a/bed.g +++ b/bed.g @@ -1,7 +1,3 @@ -; bed.g -; called to perform automatic bed compensation via G32 - - ; this script compensates for what the Z offset is ; so if G31 P500 X-30 Y-15 Z1.7 then first probe will be at ; X30 Y20 (when G30 P0 X0 Y5) @@ -9,7 +5,7 @@ M561 ; clear any bed transform G30 P0 X5 Y5 Z-99999 ; probe near a leadscrew -G30 P1 X150 Y485 Z-99999 ; probe near a leadscrew -G30 P2 X470 Y5 Z-99999 S3 ; probe near a leadscrew and calibrate 3 motors +G30 P1 X150 Y285 Z-99999 ; probe near a leadscrew +G30 P2 X270 Y5 Z-99999 S3 ; probe near a leadscrew and calibrate 3 motors G29 ; probe the bed and enable compensation diff --git a/config.g b/config.g index e3edd30..be2ac5a 100644 --- a/config.g +++ b/config.g @@ -1,77 +1,91 @@ -; Configuration file for Duet 3 (firmware version 3) -; executed by the firmware on start-up -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) - ; General preferences -G90 ; send absolute coordinates... -M83 ; ...but relative extruder moves -M550 P"duet3" ; set printer name -M669 K1 ; select CoreXY mode -G29 S1 ; Set Units to Millimeters +G90 ; send absolute coordinates... +M83 ; ...but relative extruder moves +M550 P"duet3" ; set printer name +M669 K1 ; CoreXY +G29 S1 ; Set Units to Millimeters + +; Network +;;M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP +;;M586 P0 S1 ; enable HTTP +;;M586 P1 S0 ; disable FTP +;;M586 P2 S0 ; disable Telnet ; Drives -M569 P0.0 S1 ; physical drive 0.0 goes forwards -M569 P0.1 S1 ; physical drive 0.0 goes forwards -M569 P0.2 S1 ; physical drive 0.0 goes forwards -M569 P0.3 S1 ; physical drive 0.3 goes forwards -M569 P0.4 S1 ; physical drive 0.4 goes forwards -M569 P0.5 S1 ; physical drive 0.5 goes forwards -M584 X0.3 Y0.4 Z0.0 Z0.1 Z0.2 E0.5 ; set drive mapping -M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation -M92 X160.00 Y160.00 Z1600.00 E420.00 ; set steps per mm -M566 X400.00 Y400.00 Z6.00 E120.00 ; set maximum instantaneous speed changes (mm/min) -M203 X10800.00 Y10800.00 Z1000.00 E3600.00 ; set maximum speeds (mm/min) -M201 X3000.00 Y3000.00 Z100.00 E3600.00 ; set accelerations (mm/s^2) -M906 X1000 Y1000 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in per cent -M84 S30 ; Set idle timeout +M569 P0.0 S1 D3 ; physical drive 0.0 goes forwards +M569 P0.1 S1 D3 ; physical drive 0.1 goes forwards +M569 P0.2 S1 D3 ; physical drive 0.2 goes forwards +M569 P0.3 S1 D3 ; physical drive 0.3 goes forwards +M569 P0.4 S1 D3 ; physical drive 0.4 goes forwards +M569 P0.5 S1 D3 ; physical drive 0.5 goes forwards +M584 X0.4 Y0.3 Z0.0:0.1:0.2 E0.5 ; set drive mapping +M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation + +M92 X160.00 Y160.00 Z1600.00 ; set steps per mm +M906 X1000 Y1000 Z800 I30 ; set motor currents (mA) and motor idle factor in per cent +M84 S30 ; Set idle timeout + +M566 X400.00 Y400.00 Z6.00 E120.00 P1 ; set maximum instantaneous speed changes (mm/min) +M203 X10800.00 Y10800.00 Z1000.00 E3600.00 ; set maximum speeds (mm/min) +M201 X3000.00 Y3000.00 Z100.00 E3600.00 ; set accelerations (mm/s^2) ; Axis Limits -M208 X0 Y0 Z0 S1 ; set axis minima -M208 X500 Y500 Z500 S0 ; set axis maxima +M208 X0 Y0 Z0 S1 ; set axis minima +M208 X510 Y500 Z500 S0 ; set axis maxima ; Endstops -M574 X2 S1 P"!io1.in" ; configure active-high endstop for high end on X via pin !io1.in -M574 Y2 S1 P"!io2.in" ; configure active-high endstop for high end on Y via pin !io2.in -M574 Z1 S2 ; configure Z-probe endstop for low end on Z +M574 X1 S1 P"io2.in" ; configure active high endstops +M574 Y2 S1 P"io1.in" ; configure active high endstops +M574 Z1 S2 ; configure Z-probe endstop for low end on Z -; Z-Probe -M950 S0 C"io7.out" ; create servo pin 0 for BLTouch -M558 P9 C"io7.in" H5 F400 T5000 ; set Z probe type to bltouch and the dive height + speeds -G31 P25 X-28 Y-13 Z0.9 ; set Z probe trigger value, offset and trigger height - -M671 X-4.5:250:504.5 Y-4.52:505:-4.52 S5 ; define positions of Z leadscrews or bed levelling screws -M557 X15:500 Y15:500 S100 ; define mesh grid +M671 X-4.5:250:504.5 Y-4.52:505:-4.52 S5 ; define positions of Z leadscrews or bed levelling screws +M557 X30:500 Y15:500 P5 ; define 5x5 mesh grid ; Heaters -M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 -M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0 -M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit -M140 H0 ; map heated bed to heater 0 -M143 H0 S95 ; set temperature limit for heater 0 to 95C -M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1 -M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1 -M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit -M143 H1 S280 ; set temperature limit for heater 1 to 280C +M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed" ; configure sensor 0 as thermistor on pin temp0 +M950 H0 C"out1" T0 ; create bed heater output on out5 and map it to sensor 0 +M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit +M140 H0 ; map heated bed to heater 0 +M143 H0 S110 ; set temperature limit for heater 0 to 110C + +;; Run Bed PID Tune!! Bellow is an example for a 300x300 bed +;; M307 H0 A303.1 C356.7 D1.4 S1.00 V24.0 B0 ; Fans -M950 F0 C"out4" Q500 ; create fan 0 on pin out4 and set its frequency -M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off -M950 F1 C"out5" Q500 ; create fan 1 on pin out5 and set its frequency -M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on +M950 F0 C"out7" Q500 ; create fan 0 on pin out3 and set its frequency +M106 P0 C"Hotend Fan" S0 H1 T45 L255 ; set fan 0 name and value. Thermostatic control turned on for Hotend +M950 F1 C"out4" Q500 ; create fan 1 on pin out4 and set its frequency +M106 P1 C"Layer Fan" S0 H-1 L255 ; set fan 1 name and value. Thermostatic control is turned off ; Tools -M563 P0 S"Extruder0" D0 H1 F0 ; define tool 0 -G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets -G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C +M563 P0 D0 H1 F1 ; define tool 0 +G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets +G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C -; Custom settings are not defined +M950 H1 C"out2" T1 ; create nozzle heater output on out2 and map it to sensor 1 +M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit +M143 H1 S250 ; set the maximum temperature in C for heater -; Miscellaneous -M575 P1 S1 B57600 ; enable support for PanelDue -M501 ; load saved parameters from non-volatile memory -M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss +; EVA 2 / BMG / E3D V6 -M404 N1.75 D0.4 ; Filament width and nozzle diameter +M92 E830 ; set extruder steps per mm, 0.9 angle/step (LDO Pancake) +M906 E800 ; set extruder motor current (mA) and idle factor in per cent + +M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.060000e-8 A"Hotend" +;; Run Heater PID Tune!! +;; M307 H1 A751.5 C196.6 D4.7 S1.00 V23.9 B0 + +; Z-Probe +;; Inductive Probe +; M558 P5 C"!io3.in" H5 F400 T5000 ; set Z probe type to unmodulated and the dive height + speeds +; G31 P500 X-30 Y-15 Z0.20 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed +;; BLTouch +M950 S0 C"io7.out" ; Create a servo pin on io2 +M558 P9 C"io7.in" H5 F500 T10800 A5 ; set Z probe type to unmodulated and the dive height + speeds +G31 P25 X-28.00 Y-13.00 Z0.90 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed + +M404 N1.75 D0.4 ; Filament width and nozzle diameter T0 +; Pressure Advance +; M572 D0 S0.10 diff --git a/config.json b/config.json deleted file mode 100644 index 1d7db03..0000000 --- a/config.json +++ /dev/null @@ -1 +0,0 @@ -{"board":"duet3","expansion_boards":[],"firmware":3,"standalone":false,"nvram":true,"auto_save":{"enabled":true,"save_threshold":10,"resume_threshold":11,"gcodes_to_run":"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"},"display":{"type":0,"encoder_steps":4,"spi_frequency":2000000,"menus":[{"name":"main","value":""}],"images":[]},"panelDue":true,"geometry":{"type":"corexy","mins":[0,0,0],"maxes":[500,500,500],"delta_radius":105.6,"homed_height":250,"low_dive_height":false,"max_carriage_travel":260,"print_radius":85,"rod_length":215,"z_min":0},"drives":[{"direction":1,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":160,"instant_dv":15,"max_speed":100,"acceleration":500,"current":1000,"driver":0,"driver_v3":"0.3","endstop_pin":"!io1.in","endstop_type":1,"endstop_location":2},{"direction":1,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":160,"instant_dv":15,"max_speed":100,"acceleration":500,"current":1000,"driver":1,"driver_v3":"0.4","endstop_pin":"!io2.in","endstop_type":1,"endstop_location":2},{"direction":1,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":1600,"instant_dv":1,"max_speed":3,"acceleration":20,"current":1000,"driver":2,"driver_v3":"0.0","endstop_pin":null,"endstop":null,"endstop_type":3,"endstop_location":1},{"direction":1,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":420,"instant_dv":2,"max_speed":20,"acceleration":250,"current":800,"driver":3,"driver_v3":"0.5"}],"idle":{"used":true,"factor":40,"timeout":30},"homing_speed_fast":30,"homing_speed_slow":6,"travel_speed":100,"z_dive_height":5,"slow_homing":false,"probe":{"type":"bltouch","recovery_time":0.4,"trigger_height":2.5,"trigger_value":500,"x_offset":-28,"y_offset":-13,"speed":0.9,"deploy":true,"points":[],"pwm_channel":3,"pwm_inverted":true,"pwm_pin":"io7.out","input_pin":"io7.in","modulation_pin":null},"bed_is_nozzle":false,"bed":{"present":true,"use_pid":true,"heater":0},"chamber":{"present":false,"use_pid":false,"heater":2},"heaters":[{"temp_limit":95,"scale_factor":100,"series":2200,"thermistor":100000,"beta":4138,"a":0.0005717725,"b":0.0002416626,"c":0,"channel":0,"sensor":0,"output_pin":"out0","sensor_type":"thermistor","sensor_pin":"temp0"},{"temp_limit":280,"scale_factor":100,"series":2200,"thermistor":100000,"beta":4138,"a":0.0005717725,"b":0.0002416626,"c":0,"channel":1,"sensor":1,"output_pin":"out1","sensor_type":"thermistor","sensor_pin":"temp1"}],"num_nozzles":1,"toolchange_wait_for_temperatures":true,"generate_t_code":false,"tools":[{"mix_ratio":[],"number":0,"name":"Extruder0","extruders":[0],"heaters":[1],"fans":[0],"x_offset":0,"y_offset":0,"z_offset":0}],"compensation_x_offset":15,"compensation_y_offset":15,"peripheral_points":3,"halfway_points":3,"calibration_factors":6,"probe_radius":85,"mesh":{"x_min":15,"x_max":500,"y_min":15,"y_max":500,"radius":85,"spacing":100},"home_first":false,"orthogonal":{"compensation":false,"height":50,"deviations":[0,0,0]},"network":{"enabled":true,"mac_address":"","name":"My Printer","password":"","ssid":"","ssid_password":"","dhcp":true,"ip":"192.168.1.20","netmask":"255.255.255.0","gateway":"192.168.1.254","protocols":{"http":true,"ftp":false,"telnet":false}},"fans":[{"name":"","value":100,"inverted":false,"frequency":500,"thermostatic":false,"heaters":[],"trigger_temperature":45,"output_pin":"out4"},{"name":"","value":100,"inverted":false,"frequency":500,"thermostatic":true,"heaters":[1],"trigger_temperature":45,"output_pin":"out5"}],"custom_settings":""} \ No newline at end of file diff --git a/connections.txt b/connections.txt new file mode 100644 index 0000000..a0b86de --- /dev/null +++ b/connections.txt @@ -0,0 +1,20 @@ +io_0 - display +io_1 - y endstop +io_2 - x endstop +io_7 - bltouch + +z left - driver0 +z rear - driver1 +z right - driver2 +right motor - driver3 +left motor - driver4 +extruder motor - driver5 + +out1 - SSR +out2 - filament heater + +temp0 - bed +temp1 - filament heater thermistor + +out7 - hotend fan +out4 - layer fan diff --git a/deployprobe.g b/deployprobe.g index 7fba5ac..488ed1d 100644 --- a/deployprobe.g +++ b/deployprobe.g @@ -1,6 +1,4 @@ ; deployprobe.g -; called to deploy a physical Z probe +; Called to deploy a physical Z probe ; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) -M280 P0 S10 ; deploy BLTouch - +M280 P0 S10 ; Deploy the BLTouch pin diff --git a/homeall.g b/homeall.g index ea63b06..2202a23 100644 --- a/homeall.g +++ b/homeall.g @@ -1,45 +1,23 @@ -; homeall.g -; called to home all axes -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) -;G91 ; relative positioning -;G1 H2 Z5 F6000 ; lift Z relative to current position -;G1 H1 X505 Y505 F1800 ; move quickly to X or Y endstop and stop there (first pass) -;G1 H1 X505 ; home X axis -;G1 H1 Y505 ; home Y axis -;G1 X-5 Y-5 F6000 ; go back a few mm -;G1 H1 X505 F360 ; move slowly to X axis endstop once more (second pass) -;G1 H1 Y505 ; then move slowly to Y axis endstop -;G90 ; absolute positioning -;G1 X43 Y28 F6000 ; go to first bed probe point and home Z -;G30 ; home Z by probing the bed -; -;; Uncomment the following lines to lift Z after probing -;;G91 ; relative positioning -;;G1 Z5 F100 ; lift Z relative to current position -;;G90 ; absolute positioning - -;------------------- ; BLTouch -M280 P0 S160 ; Precautionary alarm release -M280 P0 S90 ; Ensure the pin is raised +M280 P0 S160 ; Precautionary alarm release +M280 P0 S90 ; Ensure the pin is raised G91 ; relative positioning G1 H2 Z5 F6000 ; lift Z relative to current position -G1 H1 X-625 Y605 F3600 ; move quickly to X and U axis endstops and stop there (first pass) -G1 H1 X-625 F1800 ; move quickly to X and U axis endstops and stop there (first pass) -G1 H1 Y605 F1800 ; move quickly to X and U axis endstops and stop there (first pass) -G1 H2 X5 Y-5 F6000 ; go back a few mm -G1 H1 X-625 Y605 F360 ; move slowly to X and U axis endstops once more (second pass) -G1 H1 X-625 F360 ; move slowly to X and U axis endstops once more (second pass) -G1 H1 Y605 F360 ; move slowly to X and U axis endstops once more (second pass) +G1 H1 X-625 Y605 F3600 ; move quickly to X and U axis endstops and stop there (first pass) +G1 H1 X-625 F1800 ; move quickly to X and U axis endstops and stop there (first pass) +G1 H1 Y605 F1800 ; move quickly to X and U axis endstops and stop there (first pass) +G1 H2 X5 Y-5 F6000 ; go back a few mm +G1 H1 X-625 Y605 F360 ; move slowly to X and U axis endstops once more (second pass) +G1 H1 X-625 F360 ; move slowly to X and U axis endstops once more (second pass) +G1 H1 Y605 F360 ; move slowly to X and U axis endstops once more (second pass) G90 ; absolute positioning -G1 X150 Y150 F10000 ; go to first probe point +G1 X150 Y150 F10000 ; go to first probe point G30 ; home Z by probing the bed -G91 ; relative positioning -G1 Z5 F100 ; lift Z relative to current position -G90 ; absolute positioning +G91 ; relative positioning +G1 Z5 F100 ; lift Z relative to current position +G90 ; absolute positioning G1 X0 Y0 F10000 diff --git a/homex.g b/homex.g index a5bcc57..b4eae2c 100644 --- a/homex.g +++ b/homex.g @@ -1,16 +1,3 @@ -; homex.g -; called to home the X axis -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) -;G91 ; relative positioning -;G1 H2 Z5 F6000 ; lift Z relative to current position -;G1 H1 X505 F1800 ; move quickly to X axis endstop and stop there (first pass) -;G1 X-5 F6000 ; go back a few mm -;G1 H1 X505 F360 ; move slowly to X axis endstop once more (second pass) -;G1 H2 Z-5 F6000 ; lower Z again -;G90 ; absolute positioning - -;--------------- G91 ; relative positioning ;G1 H2 Z5 F6000 ; lift Z relative to current position G1 H1 X-625 F1800 ; move quickly to X axis endstop and stop there (first pass) diff --git a/homey.g b/homey.g index 1f1bf47..b3f8453 100644 --- a/homey.g +++ b/homey.g @@ -1,16 +1,3 @@ -; homey.g -; called to home the Y axis -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) -;;G91 ; relative positioning -;;G1 H2 Z5 F6000 ; lift Z relative to current position -;;G1 H1 Y505 F1800 ; move quickly to Y axis endstop and stop there (first pass) -;;G1 Y-5 F6000 ; go back a few mm -;;G1 H1 Y505 F360 ; move slowly to Y axis endstop once more (second pass) -;;G1 H2 Z-5 F6000 ; lower Z again -;;G90 ; absolute positioning - -;--------------- G91 ; relative positioning ;G1 H2 Z5 F6000 ; lift Z relative to current position G1 H1 Y605 F1800 ; move quickly to Y axis endstop and stop there (first pass) diff --git a/homez.g b/homez.g index 738088a..ac18e59 100644 --- a/homez.g +++ b/homez.g @@ -1,20 +1,3 @@ -; homez.g -; called to home the Z axis -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) -;;G91 ; relative positioning -;;G1 H2 Z5 F6000 ; lift Z relative to current position -;;G90 ; absolute positioning -;;G1 X43 Y28 F6000 ; go to first probe point -;;G30 ; home Z by probing the bed -;; -;;; Uncomment the following lines to lift Z after probing -;;;G91 ; relative positioning -;;;G1 Z5 F100 ; lift Z relative to current position -;;;G90 ; absolute positioning - - -;--------- ; BLTouch M280 P0 S160 ; Precautionary alarm release M280 P0 S90 ; Ensure the pin is raised @@ -26,6 +9,7 @@ G1 X150 Y150 F10000 ; go to first probe point G30 ; home Z by probing the bed ; Uncomment the following lines to lift Z after probing -G91 ; relative positioning -G1 Z5 F100 ; lift Z relative to current position -G90 ; absolute positioning +;G91 ; relative positioning +;G1 Z5 F100 ; lift Z relative to current position +;G90 ; absolute positioning + diff --git a/pause.g b/pause.g deleted file mode 100644 index ce6810c..0000000 --- a/pause.g +++ /dev/null @@ -1,11 +0,0 @@ -; pause.g -; called when a print from SD card is paused -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) -M83 ; relative extruder moves -G1 E-10 F3600 ; retract 10mm of filament -G91 ; relative positioning -G1 Z5 F360 ; lift Z by 5mm -G90 ; absolute positioning -G1 X0 Y0 F6000 ; go to X=0 Y=0 - diff --git a/resume.g b/resume.g deleted file mode 100644 index 128277c..0000000 --- a/resume.g +++ /dev/null @@ -1,9 +0,0 @@ -; resume.g -; called before a print from SD card is resumed -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) -G1 R1 X0 Y0 Z5 F6000 ; go to 5mm above position of the last print move -G1 R1 X0 Y0 ; go back to the last print move -M83 ; relative extruder moves -G1 E10 F3600 ; extrude 10mm of filament - diff --git a/retractprobe.g b/retractprobe.g index dbc3bdf..902f6ee 100644 --- a/retractprobe.g +++ b/retractprobe.g @@ -1,6 +1,4 @@ ; retractprobe.g -; called to retract a physical Z probe +; Called to retract a physical Z probe ; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) -M280 P0 S90 ; retract BLTouch - +M280 P0 S90 ; Retract the BLTouch pin diff --git a/sleep.g b/sleep.g deleted file mode 100644 index 8de4591..0000000 --- a/sleep.g +++ /dev/null @@ -1,5 +0,0 @@ -; sleep.g -; called when M1 (Sleep) is being processed -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) - diff --git a/stop.g b/stop.g deleted file mode 100644 index d316f0a..0000000 --- a/stop.g +++ /dev/null @@ -1,5 +0,0 @@ -; stop.g -; called when M0 (Stop) is run (e.g. when a print from SD card is cancelled) -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) - diff --git a/tfree0.g b/tfree0.g deleted file mode 100644 index cea6577..0000000 --- a/tfree0.g +++ /dev/null @@ -1,5 +0,0 @@ -; tfree0.g -; called when tool 0 is freed -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) - diff --git a/tpost0.g b/tpost0.g deleted file mode 100644 index 14bf9e9..0000000 --- a/tpost0.g +++ /dev/null @@ -1,7 +0,0 @@ -; tpost0.g -; called after tool 0 has been selected -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) -; Wait for set temperatures to be reached -M116 P0 - diff --git a/tpre0.g b/tpre0.g deleted file mode 100644 index d160132..0000000 --- a/tpre0.g +++ /dev/null @@ -1,5 +0,0 @@ -; tpre0.g -; called before tool 0 is selected -; -; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon May 24 2021 13:04:21 GMT+0200 (Central European Summer Time) -