diff --git a/bed.g b/bed.g index 7da0fad..a778789 100644 --- a/bed.g +++ b/bed.g @@ -5,10 +5,16 @@ M561 ; clear any bed transform -G30 P5 X65 Y0 Z-99999 ; probe near a leadscrew -G30 P1 X252.5 Y450 Z-99999 ; probe near a leadscrew -G30 P2 X450 Y0 Z-99999 S3 ; probe near a leadscrew and calibrate 3 motors - -M280 P0 S160 ; clear and reset BL touch -;G29 ; probe the bed and enable compensation +G30 P0 X5 Y5 Z-99999 ; probe near a leadscrew +G30 P1 X5 Y20 Z-99999 ; probe near a leadscrew +G30 P2 X20 Y5 Z-99999 ; probe near a leadscrew +G30 P3 X230 Y470 Z-99999 ; probe near a leadscrew +G30 P4 X250 Y470 Z-99999 ; probe near a leadscrew +G30 P5 X250 Y450 Z-99999 ; probe near a leadscrew +G30 P6 X270 Y470 Z-99999 ; probe near a leadscrew +G30 P7 X470 Y20 Z-99999 ; probe near a leadscrew +G30 P8 X470 Y5 Z-99999 ; probe near a leadscrew +G30 P9 X450 Y5 Z-99999 S3 ; probe near a leadscrew and calibrate 3 motors +M280 P0 S160 ; clear and reset BL touch +G29 S1 ; probe the bed and enable compensation diff --git a/config.g b/config.g index b9eea23..2481be7 100644 --- a/config.g +++ b/config.g @@ -1,4 +1,4 @@ -; Configuration file for Duet 3 (firmware version 3) and RatRig VCore3 500^3 +; Configuration file for Duet 3 (firmware version 3) and RatRig V\Core3 500^3 ; executed by the firmware on start-up ; @@ -9,41 +9,38 @@ M550 P"vcore3" ; set printer name fqdn: vcor M669 K1 ; select CoreXY mode ; Drives -M569 P0.0 S0 D3 H50 V50 ; physical drive 0.0 goes backwards -M569 P0.1 S0 D3 H50 V50 ; physical drive 0.1 goes backwards -M569 P0.2 S0 D3 H50 V50 ; physical drive 0.2 goes backwards -M569 P0.3 S1 D3 H50 V50 ; physical drive 0.3 goes forwards -M569 P0.4 S1 D3 H50 V50 ; physical drive 0.4 goes forwards -M569 P0.5 S0 D3 H50 V50 ; physical drive 0.5 goes backwards -M584 X0.3 Y0.4 Z0.0:0.1:0.2 E0.5 ; set drive mapping -M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation - -M92 X80.00 Y80.00 Z1600.00 E835 ; set steps per mm -M566 X400.00 Y400.00 Z6.00 E120.00 P1 ; set maximum instantaneous speed changes (mm/min) -M203 X20800.00 Y20800.00 Z1000.00 E3600.00 ; set maximum speeds (mm/min) -M201 X6000.00 Y6000.00 Z3000.00 E3600.00 ; set accelerations (mm/s^2) -M906 X2000 Y2000 Z1200 E800 I20 ; set motor currents (mA) and motor idle factor in per cent -M84 S30 ; Set idle timeout +M569 P0.0 S0 D3 H50 V50 ; physical drive 0.0 goes backwards +M569 P0.1 S0 D3 H50 V50 ; physical drive 0.1 goes backwards +M569 P0.2 S0 D3 H50 V50 ; physical drive 0.2 goes backwards +M569 P0.3 S1 D3 H50 V50 ; physical drive 0.3 goes forwards +M569 P0.4 S1 D3 H50 V50 ; physical drive 0.4 goes forwards +M569 P0.5 S0 D3 H50 V50 ; physical drive 0.5 goes backwards +M584 X0.3 Y0.4 Z0.2:0.1:0.0 E0.5 ; set drive mapping +M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation +M92 X80.00 Y80.00 Z1600.00 E835 ; set steps per mm +M566 X400.00 Y400.00 Z6.00 E120.00 P1 ; set maximum instantaneous speed changes (mm/min) +M203 X20800.00 Y20800.00 Z1000.00 E3600.00 ; set maximum speeds (mm/min) +M201 X6000.00 Y6000.00 Z3000.00 E3600.00 ; set accelerations (mm/s^2) +M906 X2000 Y2000 Z1200 E800 I20 ; set motor currents (mA) and motor idle factor in per cent +M84 S30 ; Set idle timeout ; Axis Limits -M208 X5 Y5 Z0 S1 ; set axis minima -M208 X500 Y500 Z500 S0 ; set axis maxima +M208 X0 Y0 Z0 S1 ; set axis minima +M208 X500 Y500 Z500 S0 ; set axis maxima ; Endstops -M574 X1 S1 P"io2.in" ; configure active-high endstop -M574 Y2 S1 P"io1.in" ; configure active-high endstop - +M574 X1 S1 P"io2.in" ; configure active-high endstop +M574 Y2 S1 P"io1.in" ; configure active-high endstop ; Z-Probe -M950 S0 C"io7.out" ; create servo pin 0 for BLTouch -M558 P9 C"^io7.in" H3 F250 T12000 A3 ; set Z probe type to bltouch and the dive height + speeds, run probing 3x +M950 S0 C"io7.out" ; create servo pin 0 for BLTouch +M558 P9 C"^io7.in" H2 F200 T10000 A5 ; set Z probe type to bltouch and the dive height + speeds, run probing 5x ;; Pay special attention to the values bellow on G31, the Z value needs to be validated for your printer ;; Start with something like 0.5 ;; Documentation available: https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe -G31 P500 X-30 Y-0.5 Z2.1 ; set Z probe trigger value, offset and trigger height -;; -M671 X-12.5:250:506.5 Y-12.5:508.5:-12.5 S6 ; define positions of Z leadscrews or bed levelling screws -M557 X30:470 Y30:470 P11 ; define 11x11 mesh grid +G31 P500 X-35 Y-0.5 Z3.175 ; set Z probe trigger value, offset and trigger height +M671 X-6:250:503 Y0:511:0 S5 ; define positions of Z leadscrews or bed levelling screws +M557 X5:465 Y5:465 P20 ; define 20x20 mesh grid ; Heaters ;; BED @@ -66,7 +63,6 @@ M950 F1 C"out4" Q20 ; create fan 1 on pin out4 ;M950 F1 C"!out4+out4.tach" Q25000 ; create fan 1 on pin out4 pwm fan (4 wires) M106 P1 C"Layer fan" S0 H-1 -L255 ; set fan 1 value. Thermostatic control is turned off - ; Lights M950 P2 C"out8" ; create output for lighning via DC DC SSR @@ -75,10 +71,8 @@ M563 P0 D0 H1 F1 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C -; Custom settings are not defined - ; Filament sensor - Duet3D laser filament monitor -M591 D0 P5 C"0.io4.in" R40:120 E3.0 S1 ; Duet3D laser sensor for extruder drive 0, connected to endstop input 4 (E0), tolerance 40 to 120%, 3mm comparison length, enabled filament monitoring +M591 D0 P5 C"io3.in" R40:120 E3.0 S1 ; Duet3D laser sensor for extruder drive 0, connected to endstop input 4 (E0), tolerance 40 to 120%, 3mm comparison length, enabled filament monitoring ; Miscellaneous M575 P1 S1 B57600 ; enable support for PanelDue diff --git a/homeall.g b/homeall.g index 36e083d..53587d8 100644 --- a/homeall.g +++ b/homeall.g @@ -6,31 +6,29 @@ M280 P0 S160 ; Precautionary alarm release M280 P0 S90 ; Ensure the pin is raised +M201 X500.00 Y500.00 ; Reduce acceleration for homing moves G91 ; relative positioning -G1 H2 Z2 F10800 ; lift Z relative to current position -G1 H1 X-625 F10800 ; move quickly to X axis endstop and stop there (first pass) -G1 H2 X10 F6000 ; go back a few mm +G1 H2 Z10 F10800 ; lift Z relative to current position +G1 H1 X-625 F3600 ; move quickly to X axis endstop and stop there (first pass) +G1 H2 X20 F3000 ; go back a few mm G1 H1 X-625 F256 ; move slowly to X axis endstop once more (second pass) +M201 X3000 Y3000 ; Return to full acceleration G90 ; absolute positioning -G1 X10 F6000 ; move forward 10mm +M201 X500.00 Y500.00 ; Reduce acceleration for homing moves G91 ; relative positioning -G1 H2 Z2 F10800 ; lift Z relative to current position -G1 H1 Y625 F10800 ; move quickly to Y axis endstop and stop there (first pass) -G1 Y-10 F6000 ; go back a few mm +G1 H1 Y625 F3600 ; move quickly to Y axis endstop and stop there (first pass) +G1 Y-20 F3000 ; go back a few mm G1 H1 Y625 F256 ; move slowly to Y axis endstop once more (second pass) -G90 ; absolute positioning -G1 Y10 F6000 ; move forward 10 mm +M201 X3000 Y3000 ; Return to full acceleration -G91 ; relative positioning -G1 H2 Z5 F10800 ; lift Z relative to current position G90 ; absolute positioning -G1 X275 Y250 F10800 ; go to first probe point +G1 X250 Y250 F3600 ; go to first probe point G30 ; home Z by probing the bed - +G29 S1 ; enable compensation +G91 ; Relative positioning G1 Z10 F100 ; lift Z relative to current position G90 ; absolute positioning -G29 S1 P"heightmap.csv" ; load weightmap diff --git a/homex.g b/homex.g index b9fdca2..08ee580 100644 --- a/homex.g +++ b/homex.g @@ -1,12 +1,13 @@ ; homex.g ; called to home the X axis ; +M201 X500.00 Y500.00 ; Reduce acceleration for homing moves +G91 ; relative positioning +G1 H2 Z10 F8000 ; lift Z relative to current position +G1 H1 X-625 F3600 ; move quickly to X axis endstop and stop there (first pass) +G1 X20 F3000 ; go back a few mm +G1 H1 X-625 F256 ; move slowly to X axis endstop once more (second pass) +M201 X3000 Y3000 ; Return to full acceleration +G1 H2 Z-10 F8000 ; lower Z again +G90 ; absolute positioning -G91 ; relative positioning -G1 H2 Z2 F10800 ; lift Z relative to current position -G1 H1 X-625 F10800 ; move quickly to X axis endstop and stop there (first pass) -G1 H2 X5 F6000 ; go back a few mm -G1 H1 X-625 F256 ; move slowly to X axis endstop once more (second pass) -;G1 H2 Z-2 F10800 ; lower Z again -G90 ; absolute positioning -G1 X10 F10800 ; move forward 10mm diff --git a/homey.g b/homey.g index 53438fe..b62a689 100644 --- a/homey.g +++ b/homey.g @@ -1,12 +1,14 @@ ; homey.g ; called to home the Y axis ; - +M201 X500.00 Y500.00 ; Reduce acceleration for homing moves G91 ; relative positioning -G1 H2 Z2 F10800 ; lift Z relative to current position -G1 H1 Y625 F10800 ; move quickly to Y axis endstop and stop there (first pass) -G1 Y-10 F6000 ; go back a few mm +G1 H2 Z10 F8000 ; lift Z relative to current position +G1 H1 Y625 F3600 ; move quickly to Y axis endstop and stop there (first pass) +G1 Y-20 F3000 ; go back a few mm G1 H1 Y625 F256 ; move slowly to Y axis endstop once more (second pass) -;G1 H2 Z-2 F10800 ; lower Z again +G1 Y10 F10800 ; move forward 10 mm +M201 X3000 Y3000 ; Return to full accelerationG1 H2 Z-10 F10800 +G1 H2 Z-10 F8000 ; Lower Z relative to current position G90 ; absolute positioning -G1 Y10 F10800 ; move forward 10 mm + diff --git a/homez.g b/homez.g index 09220f8..bd591ec 100644 --- a/homez.g +++ b/homez.g @@ -6,12 +6,10 @@ M280 P0 S160 ; Reset probe G91 ; relative positioning G1 H2 Z5 F10800 ; lift Z relative to current position G90 ; absolute positioning -G1 X275 Y250 F10800 ; go to first probe point +G1 X250 Y250 F10800 ; go to first probe point G30 ; home Z by probing the bed +G29 S1 ; probe the bed and enable compensation +G91 ; relative positioning +G1 Z10 F100 ; lift Z relative to current position +G90 ; absolute positioning -; Uncomment the following lines to lift Z after probing -G91 ; relative positioning -G1 Z5 F100 ; lift Z relative to current position -G90 ; absolute positioning - -G29 S1 P"heightmap.csv" ; Load saved height map diff --git a/reprapfirmware_3.3.0-1_all.deb b/reprapfirmware_3.3.0-1_all.deb new file mode 100644 index 0000000..df7c38e Binary files /dev/null and b/reprapfirmware_3.3.0-1_all.deb differ diff --git a/resurrect.g b/resurrect.g new file mode 100644 index 0000000..b81764b --- /dev/null +++ b/resurrect.g @@ -0,0 +1,39 @@ +; File "0:/gcodes/CFFFP_accel_support.gcode" resume print after print paused at 2022-02-13 17:05 +G21 +M140 P0 S90.0 +G29 S1 +G92 X215.634 Y137.576 Z0.400 +G60 S1 +G10 P0 S230 R230 +T0 P0 +M98 P"resurrect-prologue.g" +M116 +M290 X0.000 Y0.000 Z0.000 R0 +T-1 P0 +T0 P6 +; Workplace coordinates +G10 L2 P1 X0.00 Y0.00 Z0.00 +G10 L2 P2 X0.00 Y0.00 Z0.00 +G10 L2 P3 X0.00 Y0.00 Z0.00 +G10 L2 P4 X0.00 Y0.00 Z0.00 +G10 L2 P5 X0.00 Y0.00 Z0.00 +G10 L2 P6 X0.00 Y0.00 Z0.00 +G10 L2 P7 X0.00 Y0.00 Z0.00 +G10 L2 P8 X0.00 Y0.00 Z0.00 +G10 L2 P9 X0.00 Y0.00 Z0.00 +G54 +M106 S0.00 +M106 P1 S0.00 +M116 +G92 E-1.00000 +M83 +M486 S-1 +G17 +M23 "0:/gcodes/CFFFP_accel_support.gcode" +M26 S788 +G0 F6000 Z2.400 +G0 F6000 X215.634 Y137.576 +G0 F6000 Z0.400 +G1 F600.0 P0 +G21 +M24