98 lines
5.0 KiB
Plaintext
98 lines
5.0 KiB
Plaintext
; Connect to local display
|
|
M575 P1 B57600 S1
|
|
|
|
; General preferences
|
|
G90 ; send absolute coordinates...
|
|
M83 ; ...but relative extruder moves
|
|
M550 P"Vcore3.int.lgx.io" ; set printer name
|
|
M669 K1 ; CoreXY
|
|
G29 S1 ; Set Units to Millimeters
|
|
|
|
; Network
|
|
;M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
|
|
;M586 P0 S1 ; enable HTTP
|
|
;M586 P1 S0 ; disable FTP
|
|
;;M586 P2 S0 ; disable Telnet
|
|
|
|
; Drives
|
|
M569 P0.0 S1 D3 ; physical drive 0.0 goes forwards
|
|
M569 P0.1 S1 D3 ; physical drive 0.1 goes forwards
|
|
M569 P0.2 S1 D3 ; physical drive 0.2 goes forwards
|
|
M569 P0.3 S1 D3 ; physical drive 0.3 goes forwards
|
|
M569 P0.4 S1 D3 ; physical drive 0.4 goes forwards
|
|
M569 P0.5 S1 D3 ; physical drive 0.5 goes forwards
|
|
M584 X0.4 Y0.3 Z0.0:0.1:0.2 E0.5 ; set drive mapping
|
|
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
|
|
|
|
;;M92 X80.00 Y80.00 Z800.00 ; set steps per mm
|
|
M92 X160.00 Y160.00 Z1600.00 ; set steps per mm doubled due to 0.9 per step instead of default 1.8
|
|
M906 X1000 Y1000 Z800 I30 ; set motor currents (mA) and motor idle factor in per cent
|
|
M84 S30 ; Set idle timeout
|
|
|
|
M566 X400.00 Y400.00 Z6.00 E120.00 P1 ; set maximum instantaneous speed changes (mm/min)
|
|
M203 X10800.00 Y10800.00 Z1000.00 E3600.00 ; set maximum speeds (mm/min)
|
|
M201 X3000.00 Y3000.00 Z100.00 E3600.00 ; set accelerations (mm/s^2)
|
|
|
|
; Axis Limits
|
|
M208 X0 Y0 Z0 S1 ; set axis minima
|
|
M208 X510 Y500 Z500 S0 ; set axis maxima
|
|
|
|
; Endstops
|
|
;;M574 X1 S1 P"io1.in" ; configure active high endstops
|
|
;;M574 Y2 S1 P"io2.in" ; configure active high endstops
|
|
M574 X1 S1 P"!io1.in" ; configure active low endstops
|
|
M574 Y2 S1 P"!io2.in" ; configure active low endstops
|
|
M574 Z1 S2 ; configure Z-probe endstop for low end on Z
|
|
|
|
M671 X-4.5:150:304.5 Y-4.52:305:-4.52 S5 ; define positions of Z leadscrews or bed levelling screws
|
|
M557 X30:300 Y15:300 P5 ; define 5x5 mesh grid
|
|
|
|
; Heaters
|
|
M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed" ; configure sensor 0 as thermistor on pin temp0
|
|
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
|
|
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
|
|
M140 H0 ; map heated bed to heater 0
|
|
M143 H0 S95 ; set temperature limit for heater 0 to 95C
|
|
|
|
;; Run Bed PID Tune!! Bellow is an example for a 300x300 bed
|
|
;; M307 H0 A303.1 C356.7 D1.4 S1.00 V24.0 B0 ; TODO - check values for 500x500
|
|
|
|
; Fans
|
|
M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency
|
|
M106 P0 C"Hotend Fan" S0 H1 T45 L255 ; set fan 0 name and value. Thermostatic control turned on for Hotend
|
|
M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
|
|
M106 P1 C"Layer Fan" S0 H-1 L255 ; set fan 1 name and value. Thermostatic control is turned off
|
|
|
|
; Tools
|
|
M563 P0 D0 H1 F1 ; define tool 0
|
|
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
|
|
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
|
|
|
|
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
|
|
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
|
|
M143 H1 S270 ; set the maximum temperature in C for heater
|
|
|
|
; EVA 2 / BMG / E3D V6
|
|
|
|
M92 E415 ; set extruder steps per mm, 0.9 angle/step
|
|
M906 E800 ; set extruder motor current (mA) and idle factor in per cent
|
|
|
|
M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.060000e-8 A"Hotend"
|
|
;; Run Heater PID Tune!!
|
|
;; M307 H1 A751.5 C196.6 D4.7 S1.00 V23.9 B0 ;; TODO - Check values for 500x500
|
|
|
|
; Z-Probe
|
|
;; Inductive Probe
|
|
; M558 P5 C"!io3.in" H5 F400 T5000 ; set Z probe type to unmodulated and the dive height + speeds
|
|
; G31 P500 X-30 Y-15 Z0.20 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
|
|
;; BLTouch
|
|
M950 S0 C"io8.out" ; Create a servo pin on io2
|
|
M558 P9 C"io8.in" H5 F500 T10800 A5 ; set Z probe type to unmodulated and the dive height + speeds
|
|
G31 P25 X-28.00 Y-13.00 Z0.90 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
|
|
|
|
M404 N1.75 D0.4 ; Filament width and nozzle diameter
|
|
T0
|
|
|
|
; Pressure Advance
|
|
; M572 D0 S0.10
|