| macros | ||
| .gitignore | ||
| bed.g | ||
| config.g | ||
| deployprobe.g | ||
| homeall.g | ||
| homex.g | ||
| homey.g | ||
| homez.g | ||
| pause.g | ||
| README.md | ||
| resume.g | ||
| retractprobe.g | ||
| sleep.g | ||
| stop.g | ||
| tfree0.g | ||
| tpost0.g | ||
| tpre0.g | ||
Vcore3 500^3
Purpose
Configure and document a Vcore3 from RatRig with a Duet 3 6HC. The purpose of this repo is not to have a 1 fit all solution but the solution that works for my use case, I've tryed to provide all the hardware components and their setup, this may not suit your case. If you have a suggestion please consider opening a pull request. In the other hand it may help you setup your printer in a fast way, use at your own risk. Parts of the g code are not mine and were extracted from the ratrig config, duet github repos, etc (references on the links and external sources bellow.
HW Config
- 1x Duet 3 6HC
Display
SBC
- 1x PI 4 2GB
Power supply
- 1x Meanwell 400W 24v
Steppers
- 3x z 0.9 nema 17
- 1x x 0.9 nema 17
- 1x y 0.9 nema 17
- 1x extruder 0.9 nema 17 pancake
Carriage
- 1x Eva 2.0
HotEnd
- 1x E3D V6
- 1x Bondtech BMG Extruder
Lighting
- 1x SSR 40A DC-DC)
- 2x Led strips 24v 50cm
Note: The usage of the SSR allows more lighting to be added without worries for curruent usage on the board.
Fans
Bed heater
Bed calibration tool
- 1x Bltouch 3.1
Endstops
Bed
Filament sensor
Software
Base intall
Duet light - Config link
Git config && software deployment
apt-get update && apt-get upgrade && apt-get install git
mv /opt/dsf/sd/sys /opt/dsf/sd/sys.ori
cd /opt ; git clone https://g.lgeex.com/pedro/duet_vcore3.git
mv /opt/dsf/sd/macros /opt/dsf/sd/macros.ori
chown -R dsf:dsf /opt/duet_vcore3
chmod -R g+s /opt/duet_vcore3
setfacl -R -d -m u::rwx /opt/duet_vcore3
ln -s /opt/duet_vcore3 /opt/dsf/sd/sys
ln -s /opt/duet_vcore3/macros /opt/dsf/sd/macros
Duet 3 6HC - Pins
IO
Used IO pin headers
- io_0 - display
- io_1 - y endstop
- io_2 - x endstop
- io_7 - bltouch
Stepper motors
All steppers are 0.9º
- z left - driver0 - motion backwards (looking from the back of the printer)
- z rear - driver1 - motion backwards
- z right - driver2 - motion backwards
- top right motor - driver3 - Y - motion forwards (looking from the back of the printer)
- top left motor - driver4 - X - motion forwards
- extruder motor - driver5 - motion forwards
Outputs
Heating elements (24v)
Heating elements in use:
- out1 - SSR Bed
- out2 - Hotend
Fans (24v)
Fans in use:
- out4 - layer fan
- out7 - hotend fan
Lighting
- out8 - dc ssr operated leds
Temperature probes
Thermal probes in use:
- temp0 - Bed thermistor
- temp1 - Hotend thermistor
TODO
-
Setup filament sensor
-
All macros are untested until stated otherwise
-
Tested macros
-
- Lighting (all)
-
- Preheat (all)
-
- PID tuning Bed && HotEnd