Add A paramenter to M591

Tune the printer for new nozzle
Move Accelleromenter config to the end of the config file
2023-04-29 11:26:48 +01:00 · 2023-04-29 11:22:39 +01:00 · 2023-04-02 21:22:17 +01:00 · 2023-04-02 11:57:23 +01:00 · 2022-03-14 20:20:26 +00:00
3 changed files with 22 additions and 21 deletions
--- a/bed.g
+++ b/bed.g
@@ -4,9 +4,9 @@


 M561 ; clear any bed transform
-G30 P0 X50 Y50 Z-99999      ; probe near a leadscrew
-G30 P1 X70 Y50 Z-99999     ; probe near a leadscrew
-G30 P2 X50 Y70 Z-99999     ; probe near a leadscrew
+G30 P0 X10 Y10 Z-99999      ; probe near a leadscrew
+G30 P1 X60 Y10 Z-99999     ; probe near a leadscrew
+G30 P2 X60 Y60 Z-99999     ; probe near a leadscrew
 G30 P3 X230 Y470 Z-99999  ; probe near a leadscrew
 G30 P4 X250 Y470 Z-99999  ; probe near a leadscrew
 G30 P5 X250 Y450 Z-99999  ; probe near a leadscrew
--- a/config.g
+++ b/config.g
@@ -18,10 +18,10 @@ M569 P0.5 S0 D2 H500 V500                          ; physical drive 0.5 goes bac
 M584 X0.3 Y0.4 Z0.2:0.1:0.0 E0.5                   ; set drive mapping
 M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
 M92 X80.00 Y80.00 Z1600.00 E794                    ; set steps per mm
-M566 X500.00 Y500.00 Z4.00 E120.00 P1              ; set maximum instantaneous speed changes (mm/min)
+M566 X400.00 Y400.00 Z6.00 E120.00 P1              ; set maximum instantaneous speed changes (mm/min)
 M203 X10800.00 Y10800.00 Z1000.00 E3600.00         ; set maximum speeds (mm/min)
-M201 X10800.00 Y10800.00 Z400.00 E3600.00          ; set accelerations (mm/s^2)
-M906 X1500 Y1500 Z1500 E800 I20                    ; set motor currents (mA) and motor idle factor in per cent
+M201 X3000 Y3000 Z100.00 E3600.00                  ; set accelerations (mm/s^2)
+M906 X1700 Y1700 Z800 E800 I20                     ; set motor currents (mA) and motor idle factor in per cent
 M84 S30                                            ; Set idle timeout

 ; Axis Limits
@@ -39,9 +39,9 @@ M558 P9 C"^io7.in" H5 F300 T10000 A5 S0.05 R0.2    ; set Z probe type to bltouch
 ;; Pay special attention to the values bellow on G31, the Z value needs to be validated for your printer
 ;; Start with something like 0.5
 ;; Documentation available: https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe
-G31 P500 X-35 Y-0.5 Z2.75                          ; set Z probe trigger value, offset and trigger height (90 ºc, 15m after reaching temp)
-M671 X-6:250:503 Y0:511:0 S100                     ; define positions of Z leadscrews or bed levelling screws
-M557 X5:465 Y5:465 P20                             ; define 20x20 mesh grid
+G31 P500 X-35 Y-0.5 Z2.84                            ; set Z probe trigger value, offset and trigger height (90 ºc, 15m after reaching temp)
+M671 X-4.5:250:503 Y4.52:505:-4.5 S100             ; define positions of Z leadscrews or bed levelling screws
+M557 X5:465 Y5:465 P5                              ; define mesh grid

 ; Heaters
 ;; BED
@@ -51,7 +51,6 @@ M307 H0 B0 S1.00                                   ; disable bang-bang mode for
 M140 H0                                            ; map heated bed to heater 0
 M143 H0 S120                                       ; set temperature limit for heater 0 to 120C

-;; HotEnd
 M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.060000e-8 A"Hotend"       ; configure sensor 1 as thermistor on pin temp1
 M950 H1 C"out2" T1                                 ; create nozzle heater output on out2 and map it to sensor 1
 M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
@@ -62,7 +61,7 @@ M950 F0 C"out7" Q500                               ; create fan 0 on pin out7 an
 M106 P0 C"Hotend fan" S1 H1 T45                    ; set fan 0 value. Thermostatic control is turned on
 M950 F1 C"out4" Q20                                ; create fan 1 on pin out4
 ;M950 F1 C"!out4+out4.tach" Q25000                 ; create fan 1 on  pin out4 pwm fan (4 wires)
-M106 P1 C"Layer fan" S0 H-1 -L255                  ; set fan 1 value. Thermostatic control is turned off
+M106 P1 C"Layer fan" S0 H-1 L255                   ; set fan 1 value. Thermostatic control is turned off

 ; Lights
 M950 P2 C"out8"                                    ; create output for lighning via DC DC SSR
@@ -73,16 +72,7 @@ G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
 G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

 ; Filament sensor - Duet3D laser filament monitor
-M591 D0 P5 C"io3.in" R30:125 E5.0 S1               ; Duet3D laser sensor for extruder drive 0, connected to endstop input 4 (E0), tolerance 30 to 125%, 5mm comparison length, enabled filament monitoring
-
-; Accelerometer - LIS3HD
-;; More info: https://duet3d.dozuki.com/Wiki/Accelerometers
-;; More info: regarding sensor orientation: https://www.dropbox.com/s/hu2w5mk57l4zqpg/Accelerometer%20Orientation.pdf
-;; Possible orientations 01,02,05,06
-M955 P0 C"spi.cs3+spi.cs2" I01 S1344 R10; all wires connected to temperature daughter board connector, Orientation 01, Sampling rate 1344, 10b resolution
-M593 P"zvd" F214.3  ; use ZVD input shaping to cancel ringing at 214Hz
-;M593 P"none"        ; disable input shaping
-;M593 P"custom" H0.4:0.7 T0.0135:0.0135 ; use custom input shaping
+M591 D0 P5 C"io3.in" R20:150 E5.0 A0 S1               ; Duet3D laser sensor for extruder drive 0, connected to endstop input 4 (E0), tolerance 30 to 125%, 5mm comparison length, enabled filament monitoring

 ; Miscellaneous
 M575 P1 S1 B57600                                  ; enable support for PanelDue
@@ -91,3 +81,14 @@ M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set tension thresholds and
 M404 N1.75 D0.4                                    ; Filament width and nozzle diameter
 ;M572 D0 S0.10  	                           ; Pressure Advance
 T0                                                 ; Define default tool
+
+; Accelerometer - LIS3HD
+;; More info: https://duet3d.dozuki.com/Wiki/Accelerometers
+;; More info: regarding sensor orientation: https://www.dropbox.com/s/hu2w5mk57l4zqpg/Accelerometer%20Orientation.pdf
+;; Possible orientations 01,02,05,06
+M955 P0 C"spi.cs3+spi.cs2" I01 S1344 R10; all wires connected to temperature daughter board connector, Orientation 01, Sampling rate 1344, 10b resolution
+M593 P"ei3" F38      ; use P "shaper" input shaping to cancel ringing at center 38Hz
+;M593 P"none"        ; disable input shaping
+;M593 P"custom" H0.4:0.7 T0.0135:0.0135 ; use custom input shaping
+
+
--- a/reprapfirmware_3.4.5-1_all.deb
+++ b/reprapfirmware_3.4.5-1_all.deb
Author	SHA1	Message	Date
pedro	d13779c7d0	Add A paramenter to M591	2023-04-29 11:26:48 +01:00
pedro	b6b73ae559	Tune the printer for new nozzle	2023-04-29 11:22:39 +01:00
pedro	7f3e535160	Move Accelleromenter config to the end of the config file The accelormeter is not always connected thus and error is produced, I prefer to have the error after all configs are loaded.	2023-04-02 21:22:17 +01:00
pedro	afe26f9ee5	Bug fixes, new calibration values Fix typo in config "extra -" Calibrate accelerometer values Calibrate z offset	2023-04-02 11:57:23 +01:00
pedro	ab66b295dd	Tunes * Tune ressonance frequency * Tune stepper currents * Tune nozzle offset (new nozzle)	2022-03-14 20:20:26 +00:00