d48ea62f2b
Revert bed mesh settings
2021-06-29 19:19:27 +01:00
eefdd39236
Add setting for 1.8 x y steppers, update README.md
2021-06-28 21:01:21 +01:00
881990dcd5
Set min, max for extra safety (leds)
2021-06-27 23:37:23 +01:00
5bad296a0e
Tune bed probing after nozzle change
2021-06-27 18:22:12 +01:00
73e398c2fd
General improvements, E steps, currents, Z probe offset
2021-06-20 19:53:54 +01:00
65fb7e50e0
Fix: speed and accell settings
2021-06-17 00:01:48 +01:00
bf0950c9b9
Update motor current to 85% of max current
2021-06-16 23:19:27 +01:00
2f95b4260d
Revert x y min settings
2021-06-16 22:33:49 +01:00
7833cb37da
Update min x y
2021-06-16 22:31:54 +01:00
89b2f192e9
Disable filament sensor
2021-06-16 22:05:57 +01:00
dc6db04ebc
Auto load weight map after homing Z
2021-06-16 21:28:28 +01:00
79a7ec747c
Define stepper parameter
...
* Decrease max current in steppers
* Decrease max acceleration for x y z
2021-06-16 19:06:07 +00:00
94bf56688a
Add support to duet laser filament sensor
2021-06-15 23:09:18 +00:00
820de279bd
mend
2021-06-15 19:06:10 +00:00
439d7b4048
Fix and improve bed sensing
...
Fixing:
* bed screws location
* bed screws order
* X max 510 -> 500
Improvements:
* Probing points
* Home all speed
* Probing speed (decreased speed for increased accuracy)
2021-06-15 00:05:44 +01:00
60629756fe
Tune E-steps, tune bed config
2021-06-13 23:54:09 +01:00
b149c189f2
Decrease acceleration due to ghosting
2021-06-12 23:38:02 +00:00
7b6037d91a
Enable pressure advance, tune Z, tune E steps
2021-06-12 23:27:58 +01:00
2773198f50
Add comment with details for future pwm fans
...
After advice from duet forums, we start preparing for the PWM fans
everywhere.
Details [here](https://forum.duet3d.com/topic/23669/pmw-fan-inversed-output/3 )
2021-06-12 14:41:59 +00:00
af4171b656
Merge branch 'master' of g.lgeex.com:3dprinting/duet_vcore3
2021-06-12 13:08:52 +01:00
82b63699b6
Improve homeall.g, aiming for a smoother homing
2021-06-11 14:42:18 +01:00
b7c7d4f9b8
Fine tune E steps
2021-06-09 20:39:36 +00:00
0e84036b5a
Update E steps config after calibration, update readme
2021-06-08 17:59:23 +01:00
1c82956e54
Increse number of probes for bed leveling (10x10)
2021-06-08 00:38:39 +01:00
d4490ce7d3
Fix: Stepper direction, endstop high position for y, homing settings
2021-06-06 18:58:36 +01:00
6726f80727
Fix: Y Stepper motion, it was inverted
2021-06-06 16:18:15 +01:00
879e7a590a
Tune stepper parameters, noise reduction 1st try
2021-06-06 12:57:26 +01:00
812f24d1cd
Tune Z probre, add warning to conf, set layer frequency
2021-06-06 12:21:38 +01:00
b0288dccc5
Add LED control and several other macros
2021-06-03 22:09:42 +00:00
root
2cb30bbf32
Define calibration mesh within bed boundaries
2021-05-30 11:42:56 +00:00
94d6a867bd
Change probe offset; trigreer bloutch reset before homing
2021-05-30 11:24:13 +00:00
945eacadbb
Change tool max temp, set parameter for layer fan
2021-05-30 10:50:14 +00:00
root
32d393afcb
Add tool definition, set correct orientation to E0 stepper
2021-05-30 10:18:43 +00:00
6eec0b6c4a
Fix bed and homing coordinates, add calibrate thermal probes, etc
2021-05-28 22:35:11 +00:00
96e4e47894
Bed calibration possible, X,Y,Z movement possible
2021-05-28 16:23:59 +00:00
694463f5fc
pmso mix generated + ratrig + pmso
2021-05-26 21:17:05 +00:00
a17a6bf707
Back to defaults with small changes
2021-05-24 17:59:23 +02:00
48926ddfcd
Initial PMSO custom config
2021-05-24 14:25:40 +02:00
07d3de604a
replace active high end stop with active low ones
2021-05-24 01:21:26 +02:00
d7ad934fd8
Set parameters for ratrig 500x500x500
2021-05-23 18:03:29 +02:00
8868cbddc8
Initial commit from RatRig
2021-05-23 14:36:07 +02:00
