|
b7c7d4f9b8
|
Fine tune E steps
|
2021-06-09 20:39:36 +00:00 |
|
|
e6d25ae5a4
|
Improve homeall.g, aiming for a smoother homing
|
2021-06-08 22:07:21 +00:00 |
|
|
0e84036b5a
|
Update E steps config after calibration, update readme
|
2021-06-08 17:59:23 +01:00 |
|
|
1c82956e54
|
Increse number of probes for bed leveling (10x10)
|
2021-06-08 00:38:39 +01:00 |
|
|
1e203738f8
|
Add new entries to the tested macros list
|
2021-06-06 20:37:25 +00:00 |
|
|
d25c4c2aa3
|
Instructions update after making the repo public
|
2021-06-06 19:06:15 +00:00 |
|
|
d4490ce7d3
|
Fix: Stepper direction, endstop high position for y, homing settings
|
2021-06-06 18:58:36 +01:00 |
|
|
093927ca94
|
Fix conflict
|
2021-06-06 16:19:51 +01:00 |
|
|
6726f80727
|
Fix: Y Stepper motion, it was inverted
|
2021-06-06 16:18:15 +01:00 |
|
|
95348794dc
|
Fix: Y Stepper motion, it was inverted
|
2021-06-06 15:10:34 +00:00 |
|
|
879e7a590a
|
Tune stepper parameters, noise reduction 1st try
|
2021-06-06 12:57:26 +01:00 |
|
|
703d1d8328
|
Merge branch 'master' of g.lgeex.com:3dprinting/duet_vcore3
|
2021-06-06 12:21:50 +01:00 |
|
|
812f24d1cd
|
Tune Z probre, add warning to conf, set layer frequency
|
2021-06-06 12:21:38 +01:00 |
|
|
10f3ce060e
|
Update readme, add info regarding backplate and hw links
|
2021-06-05 22:41:09 +00:00 |
|
|
15183926fd
|
Renamed lights macro
|
2021-06-05 21:39:58 +00:00 |
|
|
440f51008e
|
Update readme with intro section
|
2021-06-05 21:37:00 +00:00 |
|
|
047265c50f
|
Change README, add new new macros to the tested list
|
2021-06-05 21:08:59 +00:00 |
|
|
77597594ce
|
Set target tem for hotend to 250C
|
2021-06-05 20:59:16 +00:00 |
|
|
a50ea27807
|
Set calibration point for hotend at 275C
|
2021-06-05 20:30:36 +00:00 |
|
|
f0f56de8b3
|
Update README.md
|
2021-06-05 20:06:23 +00:00 |
|
|
3309acd1a6
|
Update READM.md
|
2021-06-05 19:59:12 +00:00 |
|
|
2887f4e4da
|
Set pin tune parameters for Vcore3
|
2021-06-05 19:37:21 +01:00 |
|
|
9b82d9c0a6
|
Fix: Lighting probe assignement
|
2021-06-05 17:55:44 +00:00 |
|
|
f8ac02a1a0
|
update gitignore
|
2021-06-04 23:05:18 +00:00 |
|
|
b0288dccc5
|
Add LED control and several other macros
|
2021-06-03 22:09:42 +00:00 |
|
root
|
b86b210c9b
|
Fix primary bed probing points
|
2021-05-30 11:49:38 +00:00 |
|
root
|
2cb30bbf32
|
Define calibration mesh within bed boundaries
|
2021-05-30 11:42:56 +00:00 |
|
|
94d6a867bd
|
Change probe offset; trigreer bloutch reset before homing
|
2021-05-30 11:24:13 +00:00 |
|
|
945eacadbb
|
Change tool max temp, set parameter for layer fan
|
2021-05-30 10:50:14 +00:00 |
|
root
|
f02dfc6ea6
|
Merge branch 'master' of g.lgeex.com:pedro/duet_vcore3
|
2021-05-30 10:19:03 +00:00 |
|
root
|
32d393afcb
|
Add tool definition, set correct orientation to E0 stepper
|
2021-05-30 10:18:43 +00:00 |
|
|
8c3a088261
|
Add README.md
|
2021-05-28 23:24:18 +00:00 |
|
|
b5214e2f1f
|
Add README.md
|
2021-05-28 23:20:11 +00:00 |
|
|
61869e2689
|
Add useful links to README
|
2021-05-28 23:17:36 +00:00 |
|
|
5917538795
|
Add README.md
|
2021-05-28 23:14:44 +00:00 |
|
|
6eec0b6c4a
|
Fix bed and homing coordinates, add calibrate thermal probes, etc
|
2021-05-28 22:35:11 +00:00 |
|
|
96e4e47894
|
Bed calibration possible, X,Y,Z movement possible
|
2021-05-28 16:23:59 +00:00 |
|
|
73e2095286
|
remove json
|
2021-05-26 21:26:49 +00:00 |
|
|
694463f5fc
|
pmso mix generated + ratrig + pmso
|
2021-05-26 21:17:05 +00:00 |
|
|
a17a6bf707
|
Back to defaults with small changes
|
2021-05-24 17:59:23 +02:00 |
|
|
48926ddfcd
|
Initial PMSO custom config
|
2021-05-24 14:25:40 +02:00 |
|
|
07d3de604a
|
replace active high end stop with active low ones
|
2021-05-24 01:21:26 +02:00 |
|
|
d7ad934fd8
|
Set parameters for ratrig 500x500x500
|
2021-05-23 18:03:29 +02:00 |
|
|
8868cbddc8
|
Initial commit from RatRig
|
2021-05-23 14:36:07 +02:00 |
|